,

Módulo W5100_POE_PiA Keyestudio

REF: KS0148


O W5100 é um chip de interface de internet único, com várias finalidades, para aplicação num sistema integrado, garantindo alta estabilidade e desempenho, a baixo custo. Pode ser conectado à internet sem um sistema operador e é compatível com IEEE802.3, 10BASE-T e 802.3u 100BASE-TX.

17,02 IVA INCL.

Módulo W5100_POE_PiA Keyestudio

Various interface: Direct Bus, Indirect Bus and SPI Bus
Supporting TCP/IP protocol stack of hardware, also TCP,UDP,ICMP,IGMP,IPv4,ARP and PPPoE
Up to 4 independent ports
Integrating 16KBYTE transmit-receive cache
Outputting multiple indicating information,including RX,TX,Full/Duplex,Colision,Link,Speed
Supporting automatic conversion of polarity
Coming with Internet access, dual row of 2*14 2.0mm pins

REF: KS0148 Categorias: , Etiquetas: , ,
Marca

#include 
#include 
// Enter a MAC address and IP address for your controller below.
// The IP address will be dependent on your local network:
byte mac[] = {
0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED };
IPAddress ip(192,168,1,177);//modifying according your own IP
// Initialize the Ethernet server library
// with the IP address and port you want to use
// (port 80 is default for HTTP):
EthernetServer server(80);
void setup() {
// Open serial communications and wait for port to open:
Serial.begin(9600);
while (!Serial) {
; // wait for serial port to connect. Needed for Leonardo only
}
// start the Ethernet connection and the server:
Ethernet.begin(mac, ip);
server.begin();
Serial.print("server is at ");
Serial.println(Ethernet.localIP());
}
void loop() {
// listen for incoming clients
EthernetClient client = server.available();
if (client) {
Serial.println("new client");
// an http request ends with a blank line
boolean currentLineIsBlank = true;
while (client.connected()) {
if (client.available()) {
char c = client.read();
Serial.write(c);
// if you've gotten to the end of the line (received a newline
// character) and the line is blank, the http request has ended,
// so you can send a reply
if (c == '\n' && currentLineIsBlank) {
// send a standard http response header
client.println("HTTP/1.1 200 OK");
client.println("Content-Type: text/html");
client.println("Connection: close"); // the connection will be closed after completion
//of the response
client.println("Refresh: 5"); // refresh the page automatically every 5 sec
client.println();
client.println("");
client.println("");
// output the value of each analog input pin
for (int analogChannel = 0; analogChannel < 6; analogChannel++) {
int sensorReading = analogRead(analogChannel);
client.print("analog input ");
client.print(analogChannel);
client.print(" is ");
client.print(sensorReading);
client.println("");
}
client.println("");
break;
}
if (c == '\n') {
// you're starting a new line
currentLineIsBlank = true;
}
else if (c != '\r') {
// you've gotten a character on the current line
currentLineIsBlank = false;
}
}
}
// give the web browser time to receive the data
delay(1);
// close the connection:
client.stop();
Serial.println("client disonnected");
}
}

 

Baseada em 0 avaliações

0.0 pontuação
0
0
0
0
0

Seja o primeiro a avaliar “Módulo W5100_POE_PiA Keyestudio”

Não há comentários ainda.

Também pode gostar…